Gikfun USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS Writer 25 SPI Flash AE1185 $8.96. Gikfun USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS Writer 25 SPI Flash AE1185. Flashcat USB Memory Programmer BIOS MSI EEPROM NAND SPI JTAG I2C SERIAL (includes.

Graphic shell for programming Controller software (Firmware with _wo_keys in the name without USB keyboard support, but with support for multimedia buttons and power management buttons. California driver license lookup. They are for use in android where the virtual You can put a smart keyboard from the market, for example, and use the normal version (firmware from _wo_cdc to work on android without support for composite devices. Everything works except virtual com port).

Inf virtual COM port file for windows To avoid the cursor when clicking at all, (after unpacking) put in / system / usr / idc, and set the right 644. Description Connecting Configuring joystick buttons from Reno.

Connection, steering wheel: brown — GND red — + 12V lilac — LIN bus Connection, bus: X5 / 8 and X5 / 10 together — LIN bus, you need to connect a 1K pull-up resistor between the bus and + 12V Connection, steering wheel heater: X5 / 7 and + 12V — winding of heater on relay Normally open relay contacts, one through a fuse 10 15A to + 12V, the second to the element of the heater. You can also put a P-MOSFET with a switching current of at least 10A. Implemented events (LIN event tab): — volume encoder ENCODER VOL UP, ENCODER VOL DN — press the KEY MUTE volume encoder — encoder up-down ENCODER UP, ENCODER DN — pressing the encoder up and down KEY OK — button left KEY BACKWARD — button right KEY FORWARD — menu button KEY MENU — button nav KEY NAV — button voice KEY VOICE — button heating steering KEY SW HEAT All buttons support both short and long press. Developments: — heating off SW HEAT OFF — heating is on SW HEAT ON Implemented reactions (LIN reaction tab): — turn off the steering wheel light — turn on the steering wheel light — turn off the heated steering wheel — turn on heated steering wheel at 20 ° C — turn on heated steering wheel at 25 ° C — turn on heated steering wheel at 30 ° C — turn on the heated steering wheel at 35 ° C — turn on heated steering wheel at 40 ° C When the checkbox is set, the reaction trigger has a switching effect, i.e. If something was turned off, it turns on and vice versa.

As an example, to control the heated steering wheel, you can create: LIN event, select KEY SW HEAT, long press (to protect against possible short presses), LIN reaction to turn on the steering booster at 30 ° C + trigger. And to indicate the on state of heating by the LED on the leg X6 / 6 (anode to X6 / 6, cathode on mass): On the bottom tab Conclusions for this leg, select Act output 0V, add event LIN SW HEAT ON, reaction Output X6 / 6 Full control Turn ON once add event LIN SW HEAT OFF, reaction Output X6 / 6 Full control Turn off once As an example to turn on the steering light when turning on the dimensions: connect + 12V from dimensions to say X5 / 9 is VIN1 add event Voltage VIN1> 6000mV, reaction LIN backlight turn on add event Voltage VIN1. Connecting the connector on the steering wheel: 1 GND 2 + 12V 3 LIN 4 HORN button 5 HORN button Between + 12V and LIN connect a 1K resistor X5 / 8 and X5 / 10 legs together — LIN bus Implemented events for all buttons (LIN event tab) including the horn button. All buttons support both short and long press. List a4 v kletku s ramkoj restaurant. You can also turn the button illumination on or off. By analogy with the backlight for the steering from AUDI.